Built in Digital Gauges
The ScanGaugeD features an extensive array of built-in digital gauges that are updated in real time, as you drive.
The ScanGaugeD can display up to 4 digital gauges at a time. Using the button next to each gauge position, you can quickly cycle through the available gauges to create your own custom gauge set. You can also change the units of measure between standard and metric, as well as adjust the update rate.
*Kompatibilný len s vozidlami s palubnou sústavou 12V
||Engine boost in PSI, KPA, MM, or IN if desired.
||Miles Per Gallon
Kilomteres Per Gallon
Miles Per Liter
Liters Per 100Km
Kilomteres Per Liter
||Instant fuel economy is updated about every 2 seconds at the NORMAL update rate . Small changes in throttle position or load while driving will show almost immediate changes in this gauge.
||Miles Per Hour
Kilometers Per Hour
||Speed in the units selected
||Revolutions Per Minute
||The RPM of the engine
||Throttle Position Sensor
||In some vehicles, a closed throttle will read 0 and full throttle will read 100. Other vehicles will have a higher value than 0 for a closed throttle and a full throttle value less than 100.
A vehicle with a 50/50 mix of coolant and water will not boil over until about 265˚ F at sea level. This will be reduced at higher elevations.
||Average Fuel Economy
||This is the current average fuel economy and is updated about every 2 seconds (normal rate).
||Trip Fuel Cost
||This is the total fuel cost for the current trip.
||Cost Per Mile
||Cost of fuel per mile at this time
||Normal running battery voltage is between 13 and 15. When the engine is off it should be between 11 and 13. Voltages higher than 15 volts can damage batteries and electrical components. Voltages below 13 when the vehicle is running could indicate poor charging of the battery. Voltage below 11 when the engine is off could indicate a low battery charge or a shorted battery cell.
||Intake Air Temperature
||Temperature of the air going into the engine. At highway speeds, this will typically be a few degrees higher than the outside air temperature. At idle or low speed, it may be much higher in temperature than the outside temperature due to the low airflow into the engine and the high under-hood temperatures warming it up.
||Transmission Fluid Temperature
||Transmission Fluid Temperature in degrees Fahrenheit.
||Gallons Per Hour
Liters Per Hour
||Fuel consumption rate in the selected units. This is sensitive to throttle, gear and loading changes.
||This indicates the engine oil pressure in unit PSI/IN/KPA/MM as selected by the user.
||This is a percentage of the maximum power available currently being generated. In some vehicles it is the maximum available at the present RPM.
||Displays the calculated Horsepower your vehicle is currently making. This value can be adjusted for accuracy through the Advanced Setup parameters
Measure the performance of your vehicle over short periods of time, distance and acceleration.
The Performance Monitor™ allows you to measure and record performance data. You can designate a specific digital gauge to record as well as save and recall the data of up to 8 performance runs for later review and comparison. Performance Monitor lets you step through performance run data by key increments of time, speed and distance giving you a clear picture of your vehicle’s performance.
- Record Speed & Distance in both English and Metric at key points of 60ft, 1/16, 1/8, 1/4-mile as well as at 100ft increments
- Determine your vehicle’s 0-60 time
- Measure your vehicle’s braking performance
- Save & recall performance runs
- Monitor specific Digital Gauges
- And More!
Builtin Trip Computers
5 Sets of Trip Data Stored
Multiple automatic Trip Computers keep track of everything from fuel cost, to distance traveled, and everything in between.
Automatically tracks 5 sets of trip data including Current Trip, Today’s Trip/Trip A, Previous Day’s Trip/Trip B, Current Tank Trip and Tank to Empty. Each computer stores up to as many as 9 individual parameters including:
Built In Scan Tool
Troubleshoot Your Vehicle
Modern vehicles are computer controlled, and it often takes a computer to get the information needed to repair them. ScanGaugeD™ will warn you the moment a trouble code is detected. You can also manually scan for Active, Inactive and Pending Trouble codes. ScanGauge then allows you to view the details of the code, the conditions that where present when trouble was detected and clear them.
- Warns you when a DTC (Diagnostic Trouble Code) is detected.
- Reads Active, Inactive and Pending DTCs
- Shows the conditions when trouble was detected (RPM, Coolant Temp, etc.)
- Clears trouble codes